Mendota DXV-60 Betriebsanleitung PDF herunterladen (Seite 10)

GENERAL INFORMATION

Your Mendota Gas Fireplace has a state-of-the-art co-axial direct vent, sealed combustion system. This advanced, highly

efficient system brings in outside air for combustion and efficiently heats and re-circulates room air. The Mendota system

maintains high air quality, maximizes efficiency and assures proper operation in today's "tight" homes.

SAFETY AND STRUCTURAL CONCERNS

This Fireplace must be installed and serviced by a Mendota approved service person. Any adjustments to burner, pilot,

logs or coal bed

must be made by a Mendota approved service person. If pilot goes out always wait five (5) minutes be-

fore relighting pilot.

VENTING REQUIREMENTS

ALWAYS!

This Mendota Fireplace can be vented using AMERIVENT, DURAVENT, SELKIRK METALBESTOS, SECURITY

CHIMNEY and ICC brands of coaxial pipe off the top. Use only Mendota specified vents and vent caps when installing

your fireplace. Closely follow venting locations, directions and requirements. Observe the restrictions relating to vent posi-

tion on exterior of home. Be sure all vent pipe sections are fully twist-locked and leak-proof. Be sure Milpak Sealant is

used on the inner pipe joints of all Simpson DuraVent pipe components and all adjustable pipe sections manufactured by

Simpson DuraVent and American Metals.

REMOVE THE GLASS WHEN LIGHTING THE PILOT FOR THE FIRST TIME. The burners must light immediately & the

flame must travel promptly and smoothly around "curves" and light entire burner. The flame must

not

This Mendota Direct Vent Fireplace may be placed within inches of adjacent sidewalls. (See

"lift" off burners. DO

NOT operate unit if burner does not light immediately or if flame lifts off burner.

Figure 4: Specifications &

Clearances). The fireplace may be placed directly on concrete or wood flooring. If the appliance is to be installed on car-

peting, vinyl or other combustible material other than wood flooring, the appliance shall be installed on a metal or wood

panel extending the full width and depth of the appliance. Combustible mantels may be installed above top of the heat

outlet grills. How far out the mantel may protrude past the front face of this appliance is dependent on the distance from

upper grill. See

Figure 4: Specifications & Clearances. Non-combustible (marble, brick, stone, etc.) mantels or mantels

with steel protector plate on underside can be installed at any desired height above upper grill.

Never block upper or lower grills. Always use Mendota grills and Mendota approved vent systems and vent caps.

A non-combustible hearth protector is required and must extend a minimum of 12" in front of the fireplace. If fire-

place is raised off floor 6" or more, no hearth protector is required.

HEATING PERFORMANCE

Mendota Gas Built-in Fireplaces are true, high efficiency gas heaters. With its high heat output the Mendota Fireplace will

heat a large area of your home if situated to maximize heat circulation. Air movement options for maximizing heat circula-

tion, which can be considered, are through-the-wall grills or floor grills, the continuous operation of central heating furnace

blowers, or ceiling fan. The most efficient method for overall heat distribution is a ceiling fan. The heat output of the

Fireplace can be reduced by up to 23,000 BTUH by slowly turning the Hi/Lo temperature knob on the gas valve counter

clockwise from "Hi" to "Lo" and also turning OFF the rear burner using the Rear Burner ON/OFF Switch. Blower can also

be turned down to reduce heat output.

AESTHETIC CONSIDERATIONS

Burning or static fireplaces are a major aesthetic focus in any room. Locate your gas fireplace as you would a television

set. The Mendota Hearth Gas Fireplace will be a continuing source of comfort and fascination. Corner installations will

afford you the greatest potential for viewing in many rooms.

We suggest installing the Mendota Fireplace 6 to 12 inches above the floor by utilizing an elevated hearth.

ELECTRICAL REQUIREMENTS

A 115-volt electrical service must be supplied at the fireplace location at the time of installation. It must be electrically

grounded in accordance with local codes or in their absence with current edition of the National Electric Code ANSI/NFPA

70. Electrical Service must enter this appliance at the Right Side Junction Box. Power supply to blower must be conti-

nuous. DO NOT use switches or speed control devices in power supplied to fireplace.

The blower on this appliance is equipped with a three-prong plug for protection against shock hazard and should be

plugged directly into the grounded three-prong receptacle provided with the fireplace. Do not cut or remove the grounding

prong from the plug. NOTE: The blower output can be adjusted with the Remote Transmitter. There will be delays in

blower operation during "heat-up" (approx. 10 min.) and extended blower operation during "cool-down" (approx. ½ hr.) of

unit.

Wall Thermostats are NOT recommended for this appliance. A Thermostatic Remote Transmitter is supplied with this

appliance. Consult your dealer or the Mendota Service Department if you wish otherwise.

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 ... 63 64

Kommentare zu diesen Handbüchern

Keine Kommentare

Mendota DXV-60 Betriebsanleitung Seite 10

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Kamine Mendota DXV-60